DC/AC ratio and inverter clipping calculator
Oversizing the panels against the inverter is normal, because panels rarely reach their rating. How far you can go depends on the climate: in our hourly PVGIS data a 1.3 ratio clips 1.6% of the year's energy in Denver but almost none in Chennai or Miami. Enter your array and inverter sizes to see your loss and the highest ratio that keeps it under 1%.
Clear, cold, high-altitude places clip most; hot and humid places least.
Panel wattage times the number of panels, divided by 1,000.
The inverter's continuous AC output rating (for microinverters, the sum of their ratings).
Clipping at your ratio
- DC/AC ratio
- 1.20
- Energy lost to clipping
- 0.20%
- Energy clipped per year
- 20 kWh
- Energy delivered per year
- 10,139 kWh
- Hours a year at the inverter limit
- 72
- Highest ratio under 1% clipping here
- 1.32
- Highest ratio under 2% clipping here
- 1.41
- Extra energy vs panels matched to the inverter (ratio 1.0)
- +19.8%
Modelled from hourly PVGIS output at the best fixed angle with 14% system losses. Hourly averages hide short sunny peaks, so real clipping is at least this much. East-west or shaded arrays clip less.
Clipping by ratio in this city
- 1.00
- 0.00%
- 1.10
- 0.01%
- 1.20
- 0.20%
- 1.25
- 0.43%
- 1.30
- 0.78%
- 1.40
- 1.91%
- 1.50
- 3.55%
- 1.60
- 5.58%
Defaults and sources
- Clipping by DC/AC ratio
- Hourly PVGIS 5.3 output 2020-2023 for 22 cities at the optimum fixed angle with 14% system losses; clipped energy is output above 1 kW / ratio per kW DCEuropean Commission Joint Research Centre, PVGIS 5.3 hourly series · checked Nov 10, 2026
How the calculator works
For each city we took PVGIS 5.3's hourly output for 2020-2023 for 1 kW of panels at the optimum fixed angle with 14% system losses. For each DC/AC ratio, an inverter of 1 ÷ ratio kW per kW of panels clips any hour above that level; the clipped share is the energy above the limit divided by the total.
Your result interpolates between the modelled ratios (1.0 to 1.6). Energy figures multiply the city's yearly output per kW by your array size. The gain compares your array with one sized at a 1.0 ratio on the same inverter.
DC/AC ratio and clipping: common questions
What is a good DC/AC ratio for solar?
One that keeps clipping small for your climate. In our hourly PVGIS data a ratio of 1.2 clips 0.5% or less of the year's energy in all 22 cities. The highest ratio under 1% loss is about 1.26 in Denver, 1.3-1.32 in New York, Chicago, Toronto and Montréal, about 1.4 in London, Berlin and Delhi, and above 1.5 in Miami and Chennai.
How much energy is lost to clipping at a 1.3 ratio?
Between almost nothing and 1.6% in our 22 cities: 0.0% in Chennai, 0.04% in Miami, 0.3% in London, 0.78% in New York, 0.95% in Chicago and 1.57% in Denver. Cold, clear and high-altitude sites clip most because panels run closest to their rating.
Why do hot places clip less?
Panels lose output as they heat up, so hot climates rarely see panels near their rating. In our data the highest hourly output per kW of panels was 770-850 W in Chennai, Mumbai and Delhi against about 1,000 W in Denver, Montréal and Calgary, so the same inverter limit is reached far less often.
Is clipping bad for my system?
Not in itself: the inverter simply holds its output at its rating. The question is cost. If the extra panels are cheaper than a bigger inverter and add more energy than they clip, a higher ratio pays. At 1.3 in New York, 30% more panels deliver about 29% more energy than a 1.0 ratio on the same inverter, because only 0.78% is clipped.